这个是多次输入ATBp命令后，出现的错误，看着像是fw_buf用完了导致的。
下面这个是正常的开蓝牙协议之后的打印
这张图是重新开机然后第一次正常开关蓝牙协议到出现问题的全部buf次数。
是不是在输入ATBp=0的时候，关闭蓝牙协议栈时，没有释放掉某些东西导致的这个结果
这个是多次输入ATBp命令后，出现的错误，看着像是fw_buf用完了导致的。
下面这个是正常的开蓝牙协议之后的打印
这张图是重新开机然后第一次正常开关蓝牙协议到出现问题的全部buf次数。
所以是启动失败后，搜不到 ble peripheral？
你在用哪个 SDK 版本？
通常是需要开关几次才会失败？这个次数是固定的还是会改变？
我试了一下，并没有出现像你那样的问题。
问一下你的 SDK 来源于哪里？有可能更新一下可以解决问题。
== Rtl8710c IoT Platform ==
Chip VID: 5, Ver: 3
ROM Version: v3.0
== Boot Loader ==
Jul 20 2022:18:22:42
Boot Loader <==
== RAM Start ==
Build @ 14:52:31, Jan 3 2023
$8710c>interface 0 is initialized
interface 1 is initialized
Initializing WIFI ...
[Driver]: set ssid [Aurical_2G]
scan report rssi: -20 bssid: 24:4b:fe:c4:93:50
scan report rssi: -20 bssid: 24:4b:fe:c4:93:50
[Driver]: start auth to 24:4b:fe:c4:93:50
[Driver]: auth alg = 2
[Driver]: auth success, start assoc
[Driver]: association success(res=1)
[Driver]: set pairwise key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4)
[Driver]: set group key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) keyid:2
Interface 0 IP address : 192.168.1.220
WIFI initialized
init_thread(55), Available heap 0x419fd0
#ATBp
[ATBp] Start BLE Peripheral: ATBp=1
[ATBp] Stop BLE Peripheral: ATBp=0
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
ATBp=0
[ATBp]:_AT_BLE_PERIPHERAL_[OFF]
[BLE Peripheral]BT Stack deinitalized
[MEM] After do cmd, available heap 4305968
#
ATBp=1
[ATBp]:_AT_BLE_PERIPHERAL_[ON]
BT BUILD Date: Jan 3 2023, 15:25:47
BT RESET LOG...
BT Reset ok
bt_iqk_efuse_valid: has data
hci_tp_phy_efuse[0]=0,
bt_dump_iqk: DUMP,
the IQK_xx data is 0x10d,
the IQK_yy data is 0x3ff,
the QDAC data is 0x1f,
the IDAC data is 0x21,
the QDAC2 data is 0x20,
the IDAC2 data is 0x20,
hci_read_rom_check: rom_version 0x0003, bt_hci_chip_id 0x0004
hci_rtk_parse_config: BT ADDRESS 99 88 77 44 55 66, use the default config
WRITE physical FLATK=tx_flatk=1
We use fw_buf = 0x1002b1a8, fw_len = 0x1e34, config_buf = 0x1002cfe8, config_len = 0x32
Set baudrate to 921600
hci_tp_config:BT INIT success 7
Start upperStack
[BLE peripheral] GAP stack ready
local bd addr: 0x66:55:44:77:88:99
GAP adv start
[MEM] After do cmd, available heap 4274256
#
应该是NDA的sdk,因为我看工程里面有mesh的示例
那么我建议找 NDA 联系人，要个更新版本。